RC Video's 2020

Name of Video YouTube Link Published
Review & Range Test: RadioMaster R161 SBUS - 16ch. D16 Receiver
https://youtu.be/xCi0KXquIEg
31/12/20

This is my review of the R161 SBUS receiver from RadioMaster. This video also shows me range testing the R161 telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

The R88 was kindly supplied for review by RadioMaster.

https://www.radiomasterrc.com/

Firmware:
https://www.radiomasterrc.com/downloads

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

Name of Video YouTube Link Published

OpenTX “Safe” Throttle for Fixed Wings with no Flight Controller

https://youtu.be/HwcbznWXe9U
30/12/20

This video shows you how to set up a safe throttle in your radio in OpenTX for models not using a Flight Controller normally fixed wing planes.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Review & Range Test: RadioMaster R88 SBUS - PWM 8ch. Receiver
https://youtu.be/VRGOkPtn-oc
29/12/20

This is my review of the R88 SBUS & PWM receiver from RadioMaster. This video also shows me range testing the R88 telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

The R88 was kindly supplied for review by RadioMaster.

https://www.radiomasterrc.com/

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX12 Frequency Fine Tune Multiprotocol Module with FrSky Receivers https://youtu.be/7aJ0oLFO-0U
28/12/20

If you use a multiprotocol module to connect to your receivers you need to know you have to fine frequency tune any FrSky receivers you bind to it. This video will show you how to do it in your TX12.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

RadioMaster TX12 Radio TX
https://www.banggood.com/custlink/GKmd5Qqw5S

RadioMaster:
https://www.radiomasterrc.com/

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTX Setting Up Low Flight Battery Telemetry Warnings

https://youtu.be/w9xiuE6TcYw
25/12/20

This video shows you how to set up low flight battery telemetry warnings on your radio in OpenTX.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Happy Christmas 2020

https://youtu.be/lu8yfq6a5jE
24/12/20

Happy Christmas and a Happy New Year to all my subscribers, viewers and patreon.

Thanks for watching through the year.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Review & Range Test RadioMaster R86C SBUS 8ch/PWM 6ch Receiver
https://youtu.be/eGN-b_zP5pA
24/12/20

This is my review of the R86C SBUS & PWM receiver from RadioMaster. This video also shows me range testing the R86C telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

The R86C was kindly supplied for review by RadioMaster.

https://www.radiomasterrc.com/

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

RadioMaster TX12 Setting up a Basic Quad Copter

https://youtu.be/BXwRp1mxtxg
23/12/20

This tutorial video will assist you setting up a basic quad copter model with Flight Modes and Special Functions in the RadioMaster TX12. We will also take a brief look at Betaflight Configurator to show the radio is set up correctly.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

RadioMaster TX12 Radio TX
https://www.banggood.com/custlink/GKmd5Qqw5S

RadioMaster:
https://www.radiomasterrc.com/

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Review & Range Test: RadioMaster R86 PWM 6ch. Receiver

https://youtu.be/6nxldjJLV-A
22/12/20

This is my review of the R86 PWM 6ch. receiver from RadioMaster. This video also shows me range testing the R86 telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

The R86 was kindly supplied for review by RadioMaster.

https://www.radiomasterrc.com/

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Multiprotocol Module Firmware Update v1.3.1.92 Available Now

https://youtu.be/o0BusxWUGUw
21/12/20

There is an update available for your multiprotocol module in your OpenTX RadioMaster TX16S, RadioMaster TX12 & Jumper T16, I updated my module with no problems.

To update the Multi Lua Scripts:
Download the zip file unzip and copy to your SDCard in the following folder
SCRIPTS\TOOLS and click replace.

Thanks for watching.

Happy Flying.

Please consider becoming a Patreon of my channel.

https://www.patreon.com/BillClark

Multiprotocol firmware is available here:
https://downloads.multi-module.org/

Video how to update your firmware
https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published

RadioMaster TX12 Basic 4 (5) Ch Fixed Wing Model Set Up with "Safe" Throttle, Binding.

https://youtu.be/Go2Xw5Bt8lQ
21/12/20

This tutorial video will assist you to set up a standard four channel fixed wing model using 2 servos to control the ailerons. We will also set up a timer, bind our receiver to the TX12 and most importantly set up a safe throttle.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

RadioMaster TX12 Radio TX
https://www.banggood.com/custlink/GKmd5Qqw5S

RadioMaster:
https://www.radiomasterrc.com/

Want to know more about the OpenTX timers?
https://youtu.be/_3tc2V0B3ho

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Using Your RadioMaster TX16S As A Controller for Liftoff
https://youtu.be/QeO8Ks95xyE
18/12/20

This tutorial video explains how to set up your RadioMaster TX16S as a controller for the Liftoff drone simulator.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Trainer Mode
https://youtu.be/lrpDOQUv5nk
17/12/20

This tutorial video explains how to set up trainer mode on your RadioMaster TX16S. This is the OpenTX Buddy Box system to help train RC pilots much more useful than the grab the TX back method!

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Receiver Test - TBS Crossfire 6ch PWM Nano Revisited with The TBS Diamond Antenna
https://youtu.be/3PDCRpiFtHM
16/12/20

I wanted to rerun the receiver range test for the TBS Crossfire Nano using the TBS Diamond antenna you can purchase from TBS for your transmitter. The results are again interesting.

 Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Review & Range Test: RadioMaster R84 PWM 4ch. Receiver
https://youtu.be/PthG93Tjt1A
15/12/20

This is my review of the R84 PWM receiver from RadioMaster. This video also shows me range testing the R84 telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

The R84 was kindly supplied for review by RadioMaster.

https://www.radiomasterrc.com/

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Aileron Differential Using GVs https://youtu.be/3d9JwD3oYGQ
14/12/20

This tutorial video explains what aileron differential is and how to set it up in OpenTX Companion and in your TX16S using GV’s which are a very powerful tool within OpenTX. GV’s are Global Variables

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published
RadioMaster TX16S Setting Up A Elevons On A Delta Wing
https://youtu.be/59huZ9IeK6g
13/12/20

This tutorial video explains how to set up a wing plane with elevons on your RadioMaster TX16S.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Follow up review of the RadioMaster TX12 Radio

https://youtu.be/lIRgkkHGtds
12/20/20

This is a follow up to my review of the TX12. I came across a couple of problems which I gave feedback to RadioMaster and was impressed how quickly they solved these problems.

Thank you to RadioMaster for supplying the TX12 to me for review.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

RadioMaster TX12 Radio TX
https://www.banggood.com/custlink/GKmd5Qqw5S

RadioMaster:
https://www.radiomasterrc.com/

RadioMaster Downloads:
https://www.radiomasterrc.com/downloads

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Review & Range Test: RadioMaster R81 Nano Sbus Receiver

https://youtu.be/L3kcE_ehna8
11/12/20

This is my review of the R81 nano receiver from RadioMaster. This video also shows me range testing the R81 telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

The R81 was kindly supplied for review by RadioMaster.

https://www.radiomasterrc.com/

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published/

Review: Servo Tester

https://youtu.be/GQv-YE9Zp4I
11/12/20

This is a very useful item to have in your RC tool kit to help you center servos before installing into your plane or help you set up the throws without having to turn on your radio or test for binding in your control surfaces.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Servo Tester with my own money.

Servo Tester
https://www.banggood.com/custlink/33Ky5s6K5G

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published/
Receiver Test – FlySky FS-iA8X
https://youtu.be/kSNDo93Zk54
10/12/20

This video shows me range testing the FlySky FS-iA8X telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published/
Review: RadioMaster TX12 Radio
https://youtu.be/TqUhbUsESSk
09/12/20

This is my review of the TX12 compact TX from RadioMaster. I like the features it has like compact size for taking less space up in your backpack, a full size JR bay for your Crossfire module, folding handle and in radio battery charging.

It does not come with a SD card so you will need to purchase one if you would like the OpenTX features like sound warnings. To me it does feel like a hobby grade TX, the quality and feel of the plastic is good it does not have a toy feel.

The TX12 would be a good second radio to have to put in the car when out on a family trip so you can sneak in a quick flight! Great for a newcomer to the hobby who wants to try it out without the expense of a higher priced full size TX.

Thank you to RadioMaster for supplying the TX12 to me for review.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

RadioMaster TX12 Radio TX
https://www.banggood.com/custlink/GKmd5Qqw5S

Link to Manual:
RadioMaster TX12 English manual 1.0.pdf - Google Drive

RadioMaster:
Home | RadioMaster (radiomasterrc.com)

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published/

Receiver Test – Turnigy  9X8C v2

https://youtu.be/j78kdUsa31I
08/12/20

This video shows me range testing the Turnigy  9X8C v2 non telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published
RadioMaster TX16S 6 Push Buttons Uses & Setting Up
https://youtu.be/XAFa9VNGb4A
07/12/20

A subscriber as me a question about the 6 push buttons on the top of the RadioMaster TX16S. Here is my idea of some uses for the 6 buttons and how to set them up in OpenTX.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published
TBS Tracer 6ch PWM Nano Revisited with Peter the Penetrator https://youtu.be/HIv75BkvHKk 05/12/20

I wanted to rerun the receiver range test for the TBS Tracer Nano using the Peter the Penetrator antenna you can purchase from TBS for your transmitter. The results are interesting and I think it is worth getting one for your Tracer system.

 Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Multiprotocol Module Firmware Update v1.3.1.78 Available Now

https://youtu.be/yx7WZsu7jUk
04/12/20

There is an update available for your multiprotocol module in your RadioMaster TX16S & Jumper T16, I updated my module with no problems.

To update the Multi Lua Scripts:
Download the zip file unzip and copy to your SDCard in the following folder
SCRIPTS\TOOLS and click replace.

Paste the Multi.TXT file into the above folder.

Thanks for watching.

Happy Flying.

Please consider becoming a Patreon of my channel.

https://www.patreon.com/BillClark

Multiprotocol firmware is available here:
https://downloads.multi-module.org/

Video how to update your firmware
https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published

Review: FlySky FS-CVT01 Voltage Telemetry Sensor

https://youtu.be/YIrwZ08ynNs
04/12/20

This device will allow you to send back your flight battery voltage to your radio to allow you to set up low flight battery voltage warnings. You receiver will need to have a sensor port I used the FlySky iA6B receiver in my video.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the FlySky FS-CVT01 Voltage Telemetry Sensor with my own money.

FlySky FS-CVT01 Voltage Telemetry Sensor
https://www.banggood.com/custlink/vKvhF620m2

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published

Receiver Test – Hobby King HK-TR6A

https://youtu.be/VrcFN1sLkQ8
03/12/20

This video shows me range testing the Hobby King HK-TR6A non telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

RC How To Do: Motive-RC R8SB Receiver Flight Battery Telemetry

https://youtu.be/nnTonIqvVJ8
02/12/20

This video shows you how to send your flight battery voltage to your radio from the Motive-RC R8SB telemetry receiver so you can set up battery voltage warnings.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Motive-RC R8SB Telemetry Receiver with my own money.

Motive-RC R8SB Telemetry Receiver
https://www.banggood.com/custlink/GDvEVB2lPb

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Receiver Test – FlySky FS-A8S

https://youtu.be/SJIbv92lW9c
01/12/20

This video shows me range testing the FlySky FS-A8S non telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Fixed Wing Flight Modes https://youtu.be/FuRbu-zkBTc
30/11/20

This tutorial video explains how to set up flight modes for your fixed wing plane on your RadioMaster TX16S

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Swan Song For My Jumper T16

https://youtu.be/dmx8YMKswBA
28/11/20

My jumper T16 has been a very good radio even though some users have had problems mine has been fine. It has been used far more than the average RC pilot because of its appearances on my channel. I have had no problems at all just a lazy scroll wheel which is still usable.

I was not impressed with Jumper because I requested the upgraded ribbon cables so I could produce a video to show you all how to change them but Jumper just ignored me! Luckily I did not actually need them.

Other than that in my experience it has been a reliable radio.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Review: Lipo Battery Voltage Tester & Alarm

https://youtu.be/ViDP9Jb7-DI
27/11/20

This is a very useful item to have in your RC tool kit. It can also be used as a battery voltage alarm for your plane. I think it may be a bit on the heavy side for a quadcopter.

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Lipo Battery Voltage Tester & Alarm with my own money.

Lipo Battery Voltage Tester & Alarm

https://www.banggood.com/custlink/vDmRV6KBfZ

If you are in South Africa you can purchase the tester from The Flying Robot Co.

https://flyingrobot.co/products/battery-checkers

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Receiver Test – FrSky V8FR

https://youtu.be/Tfzx9xHwotA
26/11/20

This video shows me range testing the FrSky V8FR non telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
How to set up the TBS 6ch Crossfire & Tracer Nano PWM Receivers https://youtu.be/J0KluCBZgPo
25/11/20

This tutorial video will help you set up the TBS Crossfire & Tracer Nano PWM receiver for your fixed wing plane. You will also learn how to set up failsafe for you model. Thanks for watching.

Happy Flying.

Become a Patron!  

Name of Video YouTube Link Published

Receiver Test – FlySky FS-iA6B

https://youtu.be/ZJkcVLq5L98
24/11/20

This video shows me range testing the FlySky FS-iA6B telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Flaperons
https://youtu.be/eLM1RCd-iG4
23/11/20

This tutorial video explains how to set up flaperons on your RadioMaster TX16S. You do need to have a servo for each of your ailerons to make this work. Do not set up to much flaperon or you may lose aileron authority. Setting up flaperons really does help to slow your model down on approach, some models may need to add a little power on approach because the flaps may cause more drag.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTx Flight Modes (FM) and Global Variables (GV)

https://youtu.be/0bFq2aNaxRo
21/11/20

This OpenTX video is to give you and insight into OpenTX Global Variables relating to Flight Modes. This is a very powerful feature of OpenTX my example is a set up of flaps and mixing in some down elevator.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Receiver Test – FrSky V8R4

https://youtu.be/arrsXcMmomk
20/11/20

This video shows me range testing the FrSky V8R4 non telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Crow Brakes
https://youtu.be/HXSlsGTorCg
19/11/20

This tutorial video explains how to set up flaps and crow brakes for your plane normally a glider on your RadioMaster TX16S.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Receiver Test – TBS Tracer 6ch PWM Nano
https://youtu.be/nWlZQDDsMIY
18/11/20

This video shows me range testing the TBS Tracer 6ch PWM Nano telemetry receiver using my standard test procedures. The Tracer Micro TX was on full power for this test with the standard antenna. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Receiver Test – TBS Crossfire 6ch PWM Nano

https://youtu.be/xEG0uB-lRWA
17/11/20

This video shows me range testing the TBS Crossfire 6ch PWM Nano telemetry receiver using my standard test procedures. The Crossfire Micro TX V2 was on full power for this test with the standard antenna. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Flaps (Two Servos on Two Channels)
https://youtu.be/vDXRx0xBsyE
16/11/20

This tutorial video explains how to set up flaps for your plane on your RadioMaster TX16S

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Receiver Test – Motive-RC R8SB

https://youtu.be/-y9_7Cvx6Iw

15/11/20

This video shows me range testing the Motive-RC R8SB D8 compatible telemetry receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Review (well sort of!): TBS Crossfire Micro TX V2 Heat Sinks

https://youtu.be/ayUumcG4qOQ
14/11/20

TBS have released heat sinks you can purchase for your Crossfire Micro TX V2 which are only needed if you are pushing to the outer range limits of the TX. I wanted to get them so I could install them and share the process with you all.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Fixed Wing Dual Rates
https://youtu.be/rtoo9wnPftk
13/11/20

This tutorial video explains how to set up dual rates on your fixed wing plane on your RadioMaster TX16S

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Receiver Test – FrSky XM+ Receiver

https://youtu.be/ew_4TKAH7pc
12/11/20

This video shows me range testing the FrSky XM+ receiver using my standard test procedures. Please see link below for full details of how I carry out my unscientific tests. The results in my video will be available in a document file on my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Full testing video showing you how I complete my receiver tests.
https://youtu.be/Glx8jGlp9BY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published

Binding Receivers Can Be Tricky Revisited

https://youtu.be/CQ6C6rGopGc
11/11/20

I recently made a video for the RadioMaster TX16S explaining the problem you can have with binding some FrSky receivers to the multiprotocol module which also need to be RF frequency fine tuned. This was caused by a particular receiver I have needing RF frequency fine tune values of -1 and – 69 so at the default radio value of 0 it would not bind. So I wanted to share this in case other people where having the same problem. In the video I only explained verbal which from the comments below the video needs clarification. In this video I show you the problem and how to solve it.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Receiver Test – FrSky R-XSR Telemetry Receiver

https://youtu.be/Glx8jGlp9BY
10/11/20

I am going to test as many receivers as a can and post the results in a video and a document file in my google drive for you to check out. This is not a scientific test, I will follow the same procedure for all the receivers and show the results which of cause could be different in other environments.

This is not a review of the receiver.

Receiver Test Results Link
https://drive.google.com/drive/folders/1mb1nhTCaJ3qz73wusjV3j_dlOA-Ks7nY

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Fixed Wing Expo https://youtu.be/AendNkApq-4
09/11/20

This tutorial video explains what Expo is and how to implement it on your RadioMaster TX16S

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Flying My Taycan & It Happened Again!

https://youtu.be/Bd1IOvukTDk
08/11/20

Early morning Sunday flying with my Taycan the weather was forecasting high wind for later, it fell out of the sky again! Oh well that’s the hobby.

Please watch and comment to let me know what you think happened.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Fixed Wing Aileron Rudder Mixing https://youtu.be/Tu_i3WCNSoc
06/11/20

This tutorial video explains how to set up Aileron Rudder mixing on your RadioMaster TX16S. You sometimes need to do this to help a model plane yaw when making a turn. This can be done by operating both aileron and rudder sticks in flight or why not get your OpenTX computer radio to do it for you.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
OpenTx Quick Tip–Setting Up Rate Profiles To A Switch On Your Radio
https://youtu.be/rzktpQESrmQ
04/11/20

This quick tip is to show you how to set up rate profiles to a switch on your radio.

Useful if you want to try different rate profiles on the fly at the flying site without taking a computer to connect your drone to.

Thanks for watching.

Happy flying.

Making You Own Custom Sounds
https://youtu.be/aO3wYejJs00

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Battery Percentage Widget
https://youtu.be/yKirCORZX3g
03/11/20

This tutorial video shows you how to set up the battery widget on your TX16S which is different to the battery voltage.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up A Fixed Wing “Safe” Throttle https://youtu.be/MnoY7Z10pk4
02/11/20

In this tutorial video I go through the process of setting up a safe throttle for your fixed wing models. When a model use a flight controller the FC controls the safe arming of the model but with fixed wing planes we normally do not use FC’s. This video shows you how to set up a safe throttle.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Multiprotocol Module Firmware Update v1.3.1.77 Available Now https://youtu.be/p0HcWVwaR-4
31/10/20

There is an update available for your multiprotocol module in your RadioMaster TX16S & Jumper T16, I update my module with no problems.

To update the Multi Lua Scripts:
Download the zip file unzip and copy to your SDCard in the following folder
SCRIPTS\TOOLS and click replace.

Thanks for watching.

Happy Flying.

Please consider becoming a Patreon of my channel.

https://www.patreon.com/BillClark

Multiprotocol firmware is available here:
https://downloads.multi-module.org/

Video how to update your firmware
https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published
RadioMaster TX16S Screen Set Up - Widgets https://youtu.be/Cn2Khis-0JY
31/10/20

In this tutorial video we learn how to customise our opening screen on out TX16S using widgets.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTx Quick Tip – Setting Switch Default Positions

https://youtu.be/R0a3A3CIBEY
29/10/20

This OpenTX quick tip is to show you how to change your default switch positions on your radio to stop switch warnings on start up if you select not to have your switches in the forward positions. In my case I have my disarmed switch in the back position and not forward.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Hinging Control Surfaces on Balsa Model Planes https://youtu.be/ELb4CGYzk0Y
28/10/20

I have had an ongoing project for around 10 years, naughty I know! I have decided to get the Raven finished and I thought I would show you how I hinge my control surfaces so you cannot see the way it is secured. The problem I have had in the past is when trying to use superglue and trying to insert 3 hinges quickly and accurately into the wing so I do it this way.

I have never had a control surface come out, well not to date!

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Setting Up Your TX for a Quadcopter
https://youtu.be/3tsl6SHdHC4
26/10/20

In this tutorial video I go through the process of setting up a quadcopter with flight modes and switch sounds on your TX16S in OpenTX Companion and on the radio. This may not be exactly the same set up you want but I think it is a good starting point. Remember this is on the radio side of the set up you still need to go through the Betaflight settings.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published
Flaps or No Flaps?
https://youtu.be/OvNxZsVsISI
25/10/20

I have been wanting to make a video showing flaps, in my case flaperons, or not on my model. I know from the “feel” of the Clouds plane there is a difference and the plane does indeed come in slower.

My recommendation is to give it a go especially on a glider style plane or if you want shorter landings. I have not tried flaps on takeoff because I hand launch the model in this video so there is no need to.

Just as a side comment the Clouds is a nice model very noisy but tough as old boots! I have had mine many years. You can still get it but it is called AXN Floater and yes without flaperons it does indeed float on and on, see video.

This is not an affiliate link but I want you to be able to get one as it is a great plane. You must share the love!

https://hobbyking.com/en_us/h-king-axn-floater-1280mm-pnf.html

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Happy Out to Diatone Innnovations

https://youtu.be/23rZxyp6H6I
24/10/20

If I come across good or bad service from vendors I am going to let you know. This is a “happy out” my version of a “shoot out” to Diatone who gave me very good service when dealing with a problem with my Tina whoop.

Let me know in the comments section how your dealings with vendors have gone.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Binding Receivers Can Be Tricky https://youtu.be/ystSVSN-3m8
21/10/20

In this tutorial video I go through the process of binding receivers to your RadioMaster TX16S sometimes this can cause you problems. So watch this video and all will be explained.

Link to my videos:

FrSky Frequency Adj.
https://youtu.be/RDICdD4QpUk

Open TX Radio Not Binding to Frsky V8R4 Receiver
https://youtu.be/Zm5_mKAPjPU

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Basic 4 (5) Ch Fixed Wing Model Set Up https://youtu.be/vMc_7SgbP9E
19/10/20

This tutorial video will assist you to set up a standard four channel fixed wing model using 2 servos to control the ailerons. We also set up a time and widget to show the timer on the front page of your radio.

Want to know more about the OpenTX timers?
https://youtu.be/_3tc2V0B3ho

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

When Is The Last Time You Did Something For The First Time?

https://youtu.be/i8rUKRUQlgo
18/10/20

For me it was today. I decided to take the camera off my Syma, it needs a new motor and cannot get hold of one, and try flying FPV fixed wing. Yesterday I put the camera on my trusted Clouds and went out today and tried FPV. It was great but not all of the flight was FPV because I decided to land LOS until I have practiced a bit more.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

RadioMaster TX16S The Need To Fine Frequency Tune FrSky Receivers

https://youtu.be/-8T-1-KuHmo
15/10/20

If you use a multiprotocol module to connect to your receivers you need to know you have to fine frequency tune any FrSky receivers you bind to it. Here is the link to my previous video showing you how to do it.

https://youtu.be/RDICdD4QpUk

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Installing Amber Sounds https://youtu.be/Crb7V3j8OMY
14/10/20

You can change the sounds on your TX16S by downloading the Amber sound pack and copying the sounds to your radio’s SD card.

Here is how to do it.

Amber sound pack available here:
http://open-txu.org/home/version-2/v2-2-resources-2/

Peazip available here:
https://peazip.github.io/

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

RadioMaster TX16S & TBS Crossfire Micro TX Buzzing Sound Solved

https://youtu.be/BMworCXQNe0
12/10/20

I was very disappointed when I put my TBS Crossfire Micro TX module into my RadioMaster TX16S and it started making an awful buzzing sound. This for me is not good at all so I decided to see if there was anything I could do to solve it and the answer was very simple.

I hope this fix helps you if you are having the same problem.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

RadioMaster TX16S Calibrate Radio Battery

https://youtu.be/7L3lGAbwNKQ
12/10/20

We should calibrate the radio to the measured voltage of the radio’s battery. We will need a multi meter and I suggest fully charging your battery. Measure the battery voltage with the multi meter and make a note of it then enter the value in your radio as shown in this video.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Calibrate Gimbals, Rotary Switches & Sliders https://youtu.be/xT3M00a0Zl0
11/10/20

In this tutorial video we go through the process of calibrating your TX16S gimbals, rotary switches & sliders. Your radio may ask you to do this on initial start up but if it does not I think it is worthily completing the process. Then it may only need to be done if the radio requests you to do so. This can happen if your radio “bricks” or is set back to the factory settings.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Making Custom Sounds https://youtu.be/jaxaforqkdQ
08/10/20

This video will direct you to a video I made which will assist you to be able to make custom sounds for the RadioMaster TX16S. I think this is a fun way to customise your radio.

https://youtu.be/aO3wYejJs00

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

How To Update OpenTX Companion & Radio Firmware

https://youtu.be/IyVOcb64VWA
07/10/20

This video will assist you to download both the new OpenTX Companion utility and your new radio firmware. Please remember to back up your radio and model settings before proceeding with any firmware update because there is a possibility you may lose your radio and model settings in the process. This video is relevant for the Jumper T16, RadioMaster TX16S and any other OpenTX transmitter.

Download Latest OpenTX Companion Utility
If you do not already have the OpenTX Companion utility go to the link below under the News section click on the latest version. You then go to the bottom of the page to Download Links and you will see the link to download the latest OpenTX companion utility.

https://www.open-tx.org/

When there is a new OpenTX firmware, but not every time, you need to recompile your SD card contents the link below will send you to my video on how I do this.

My Video: OpenTX - My Procedure For Updating SD Card Contents
https://youtu.be/7YXfGNqSiMM
Download OpenTX SD Card Contents:
https://www.open-tx.org/
Go to News and click on latest release. Go to download links and click download SD Card contents. Then download the correct SD Card contents for your radio i.e. opentx-tx16s.

I suggest you then remove your SD Card from your radio and format it in your computer. If you have no custom sounds, custom pictures or Amber sounds just copy the contents to your radio’s SD Card and put the SD Card back in your radio and you should be good to go. You can connect your radio to your computer via the USB port and copy the files to the SD Card overwriting the contents but I prefer to remove the SD card from the computer because the process is far quicker on your computer. 

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

The Most Fun Fly Swatter!

https://youtu.be/gMIsS9uKLdw
07/10/20

Not sure if you have had this problem but flying back last summer flies brought down my BetaFPV 75X. Today I was flying my Diatone Taycan and they attacked the quad and I filmed them with my GoPro.

Any ideas why flies do this?

Let me know in the comments section below.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTX Firmware Update 2.3.10 Available Now

https://youtu.be/bkrHfVeA_og
06/10/20

There is an update available for OpenTX version 2.3.10 which is available for download now. I have updated my radio with no problems or error messages.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Open TX
https://www.open-tx.org/

Video how to update your firmware
https://youtu.be/l4YE5nBe-lw

OpenTX - My Procedure For Updating SD Card Contents
https://youtu.be/7YXfGNqSiMM

Name of Video YouTube Link Published

RadioMaster TX16S Update Internal Multiprotocol Module

https://youtu.be/mgKwqnZemfc
06/10/20

In this video we update the multiprotocol module in your RadioMaster TX16S.

You can get the firmware updates from this link.
https://downloads.multi-module.org/

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Just Cruising My African Back Yard

https://youtu.be/7KAZLhJfoWA
05/10/20

Another FPV flight with my Diatone Taycan the sun was going down and the windy calming so I flew my African back yard what a stunning landscape.

Music:

♫Tribal War Council♫
Doug Maxwell Media Right Productions

♫At The Shore - The Dark Continent♫

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S Compiling SD Card Contents
https://youtu.be/Doca8HLjGh4
05/10/20

This video is to help you compile your OpenTX SD Card for your TX16S. I am going to forward you to my OpenTX playlist to show you how I save all my custom pictures, custom sounds & Amber sound. If you are new to your RadioMaster TX16S and OpenTX this may be a foreign language to you at the moment because I have not reached these subjects in my TX16S playlist yet.

When there is a new OpenTX firmware, but not every time, you need to recompile your SD card contents the link below will send you to my video on how I do this.

My Video: OpenTX - My Procedure For Updating SD Card Contents
https://youtu.be/7YXfGNqSiMM
Download OpenTX SD Card Contents:
https://www.open-tx.org/
Go to News and click on latest release. Go to download links and click download SD Card contents. Then download the correct SD Card contents for your radio i.e. opentx-tx16s.

I suggest you then remove your SD Card from your TX16S and format it in your computer. If you have no custom sounds, custom pictures or Amber sounds just copy the contents to your radio’s SD Card and put the SD Card back in your radio and you should be good to go. You can connect your radio to your computer via the top USB-C port and copy the files to the SD Card overwriting the contents but I prefer to remove the SD card from the computer because the process is far quicker on your computer. 

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals
Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RadioMaster TX16S OpenTX Flight Timer Options
https://youtu.be/KK4pYQw2z3A
04/10/20

I am going to direct you to a previous video I made explaining the timer option you have within OpenTX in your RadioMaster TX16S.

https://youtu.be/_3tc2V0B3ho

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published

Just a FPV Flight, Great Fun!

https://youtu.be/0FN3VG2M2Mg
03/10/20

Just a video of me flying my Taycan around a derelict building. It is what my channel is about, me getting out in the fresh air and flying my drone and hopeful helping you to do the same.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published

RadioMaster TX16S Set Up Companion, Backup & Update Firmware

https://youtu.be/1oD9E4klTUc
30/09/20

This video in the RadioMaster TX16S playlist will assist you to back up your radio and model settings to OpenTX Companion and show you how to update the firmware on your TX16S.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals

Download OpenTX Companion:
https://www.open-tx.org/
Go to News and click on latest release. Go to download links and download the companion for your computers operating system.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Diatone Taycan VTX Range Test at 500 Metres

https://youtu.be/O6LmmdB3uXE

28/09/20

After the fall out of the sky uncontrolled landing my Taycan’s VX400 VTX was showing signs of diminished power output. I decided to replace it which was the right thing to do range is around twice as much now.

Here is my video of the test flight.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Turnigy TGY 9X – Setting Up Aileron Rudder Mixing

https://youtu.be/2SKnKHmDN9g
27/09/20

This video will help you set up aileron rudder mixing on your Turnigy TGY 9X.

I have only one plane which I use this function because it developed problems instigating a turn so you mix a little rudder in with the aileron stick to help yaw the plane. You of cause can do this manually which I did before using aileron rudder mixing.

Just experiment with the amount of rudder until you are happy with the feel of the controls.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Multiprotocol Module Firmware Update v1.3.1.69 Available Now

https://youtu.be/zUq3cxMHWZM
24/09/20

There is an update available for your multiprotocol module in your RadioMaster TX16S & Jumper T16, I update my module with no problems.

To update the Multi Lua Scripts:
Download the zip file unzip and copy to your SDCard in the following folder
SCRIPTS\TOOLS and click replace.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Multiprotocol firmware is available here:
https://downloads.multi-module.org/

Video how to update your firmware
https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published
RadioMaster TX16S Conversion from Mode 2 to Mode 1 https://youtu.be/CPzMViEBUXY
25/09/20

I fly RC models in Mode 1 which means my throttle is on the right stick. My TX16S came set up in Mode 2 so I need to swop the gimbals over and reprogram the radio to Mode 1 this process is not difficult.

I purchased my TX16S from the Flying Robot Co in Cape Town. This is not an affiliate link but I want to share where you can get yourself a RadioMaster TX16S in South Africa.

 https://flyingrobot.co/collections/tx/products/preorder-radiomaster-tx16s-hall-sensor-gimbals

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Multiprotocol Module Update v1.3.1.65 Available Now https://youtu.be/UEYdHDFLu28
21/09/20

There is an update available for your multiprotocol module in your Jumper T16 I update my module with no problems.

Please check the bootloader details on the following page.

https://github.com/benlye/flash-multi/blob/master/doc/New_Bootloader.md

To update the Multi Lua Scripts:
Download the zip file unzip and copy to your SDCard in the following folder
SCRIPTS\TOOLS and click replace.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published
Turnigy TGY 9X – Setting Up Expo
https://youtu.be/7pvlOvsF6wg
18/09/20

This video shows you how to set up expo on your Turnigy TGY 9X for your fixed wing planes.

If you would like me to produce a video on a specific aspect of the Turnigy TGY 9X please leave your suggestions in the comments section below.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Diatone Tina Whoop DVR Footage Just Having Fun

https://youtu.be/af-19XzatBQ
17/09/20

I wanted to record some DVR footage to show you how much fun the Diatone Tina Whoop is I hope you enjoy it.

Thanks for watching.

Happy Flying.

Music:
Gold In Them Hills
Nathan Moore

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Diatone Taycan Following In The Footsteps https://youtu.be/7HvjdZySnHE
14/09/20

I took my Taycan to the “volcano” hill to go fly round it, it is a very interesting rock formation. Someone has climbed it and put a flag up on the top but I could not make out what the flag is. My Syma quad did this journey but had a problem and dropped out of the sky it was an effort to retrieve it but this time all was good.

I am trying to fly the Taycan, which is a cinewhoop, smoothly to get nice footage of the area where I live, slowly getting there!

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Turnigy TGY 9X – Setting Up Dual Rates

https://youtu.be/hHJdqI8Zhog
09/09/20

This video shows you how to set up dual rates on your Turnigy TGY 9X for your fixed wing planes.

If you would like me to produce a video on a specific aspect of the Turnigy TGY 9X please leave your suggestions in the comments section below.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Diatone Taycan Mountain Hike

https://youtu.be/x-d3B0I5qjk
07/09/20

This is a drone flight where I took my Diatone Taycan on the same adventure as my Syma but this time it was far less scary because of the telemetry coming back to my radio and the OSD information.

I am new to TBS Crossfire and it is so nice having the knowledge you have a very reliable link between your drone or RC plane even when only flying up to 500 metres away from you. This flight was only 218 metres from home.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

TBS Crossfire Micro TX Firmware Update 4.02

https://youtu.be/f5RQBBpDiZA
04/09/20

This video will show you how to update your micro TX using Agent X app. I will also run through the updating of my Nano RX.

Thanks for watching.

Happy flying.

Updating TBS AgentX App:

https://youtu.be/tCM-BTR5RQU

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

How To Update The TBS AgentX App

https://youtu.be/tCM-BTR5RQU
02/09/20

This video will show you how to update your Agent X app which TBS have made very easy.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.1.59 Available Now

https://youtu.be/XQJAS-yeeug
31/08/20

There is an update available for your multiprotocol module in your Jumper T16 I update my module with no problems.

To update the Multi Lua Scripts:
Download the zip file unzip and copy to your SDCard in the following folder
SCRIPTS\TOOLS and click replace.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTx Quick Tip – Setting Up Flip Over After Crash (Turtle) Mode

https://youtu.be/Nuf3YptbjXw
31/08/20

This quick tip is to show you how to set up Flip Over After Crash Mode which is also known as Turtle Mode. Just be careful with this function if used incorrectly can burn out your ESC or motors.

It is useful so you do not need to walk to your quad if it lands upside down to get it in the air again. Though the exercise would be good for you!

Thanks for watching.

Happy flying.

Making You Own Custom Sounds
https://youtu.be/aO3wYejJs00

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTx Quick Tip – Adding Sound Volume To Your Radio

https://youtu.be/Ctu4z86QINo
28/08/20

This quick tip is to show you how to control the sound volume on your OpenTX radio using a rotary switch.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTx Quick Tip – Setting Up Telemetry Data Logging to your Radio

https://youtu.be/LdtpuH7zUbA
26/08/20

This quick tip is to help you set up Telemetry Data logging on your OpenTX Radio. This function is very useful for locating your model if you lose it and you have a GPS module on your model. I would recommend adding a GPS module to your drone for this purpose. I show how to set this up in OpenTX Companion and on my JumperT16.

Thanks for watching.

Happy flying.

Review: Team Black Sheep M8 GLONASS GPS Module

https://youtu.be/In5TTsT4mlY

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTx Quick Tip - TBS Crossfire Telemetry Link Quality Warnings

https://youtu.be/X1vzqW7E5aQ
24/08/20

This quick tip shows you how to set up TBS Crossfire link quality telemetry warnings in your OpenTX radio. I show you how to on both the Jumper T16 and within OpenTx Companion.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

TBS Crossfire – Intro to the TBS Crossfire Micro TX II Part II

https://youtu.be/lfIcCCLjdHY
21/08/20

I have just received my TBS Crossfire Micro TX and installed it into my Diatone Taycan and Jumper T16 works great and very easy to set up. I love the OTA updating of the TBS Crossfire receivers fantastic!

Let’s take a look at the installation process in OpenTX & Betaflight and how to wire your TBS Nano RX to your flight controller.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Links:

https://www.team-blacksheep.com/

Team Black Sheep Agent X App.

https://www.team-blacksheep.com/products/prod:agentx

Name of Video YouTube Link Published

TBS Crossfire – Intro to the TBS Crossfire Micro TX II

https://youtu.be/6VBtWQkZr_0
19/08/20

I have just received my TBS Crossfire Micro TX and installed it into my Diatone Taycan and Jumper T16 works great and very easy to set up. I love the OTA updating of the TBS Crossfire receivers fantastic!

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Links:

https://www.team-blacksheep.com/

Team Black Sheep Agent X App.

https://www.team-blacksheep.com/products/prod:agentx

Name of Video YouTube Link Published
OpenTx Quick Tip – Setting Up Lost Quad (Motor) Beeper https://youtu.be/BfiUSf1en6A
12/08/20

How to set up a lost quad motor beeper.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Bind Tone When Flying?!
https://youtu.be/OtlJPCa6qkM
11/08/20

I have experienced on at least 2 occasions my Jumper T16 emitting the bind tone when my radio is already bound to a model. A viewer posted a comment about the same problem they were having so this is a request to other Jumper T16’s owners who may be having the same thing happen with their radio to let me know.

I have made contact with Jumper and they require a video of the problem so they can investigate it. If this happens to your radio please try and video it and send it to me at

bill@triplemadventures.co.za

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark
Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.1.49 Available Now

https://youtu.be/L7exZftDsqI
03/08/20

There is an update available for your multiprotocol module in your Jumper T16 I update my module with no problems.

To update the Multi Lua Scripts:
Download the zip file unzip and copy to your SDCard in the following folder
SCRIPTS\TOOLS and click replace.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published

Basic Quad Copter Set Up Part 9 The FPV Flights

https://youtu.be/gbOFtgUrICM
27/07/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX and Betaflight. Now the bit we have been building up to the FPV flights.

This tutorial is from a newbie’s point of view, I have only set up 2 quad copters before this one. I have set many fixed wing planes over the years oh and 1 toy grade quad copter which is set up very differently.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Music: Wings of Spring - The 126ers

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO
https://www.banggood.com/custlink/D3mYJmZF1z

Name of Video YouTube Link Published

Basic Quad Copter Set Up Part 8 Smart Audio

https://youtu.be/5TuSG6SyLkY
24/07/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX and Betaflight. Here I go through a basic look at Smart Audio.

This tutorial is from a newbie’s point of view, I have only set up 2 quad copters before this one. I have set many fixed wing planes over the years oh and 1 toy grade quad copter which is set up very differently.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO
https://www.banggood.com/custlink/D3mYJmZF1z

Name of Video YouTube Link Published

Basic Quad Copter Set Up Part 7 Betaflight Battery Configuration

https://youtu.be/wii_BtvjP6s
20/07/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX and Betaflight. Here I go through setting up Betaflight battery configuration.

This tutorial is from a newbie’s point of view, I have only set up 2 quad copters before this one. I have set many fixed wing planes over the years oh and 1 toy grade quad copter which is set up very differently.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO

https://www.banggood.com/custlink/D3mYJmZF1z
Name of Video YouTube Link Published

Basic Quad Copter Set Up Part 6 End Points & Forwarding RSSI

https://youtu.be/PPrc4tfCKS8
15/07/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX and Betaflight. Here I go through setting up End Points & forwarding RSSI to your radio.

This tutorial is from a newbie’s point of view, I have only set up 2 quad copters before this one. I have set many fixed wing planes over the years oh and 1 toy grade quad copter which is set up very differently.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO
https://www.banggood.com/custlink/vv3YhAbVlH

Name of Video YouTube Link Published

OpenTx Quick Tip - Mute Playing Sound Tracks on Radio Start Up

https://youtu.be/gFGSaJDwn2c
14/07/20

I am going to make quick tip videos for OpenTX this one is about muting sound tracks that are attached to your radios switches and sound when you turn your radio on.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Battery Internal Resistance (IR)

https://youtu.be/59Sgt-FZNdQ
13/07/20

This video came about because I purchased an iSDT Q8 charger from the Flying Robot Co in Cape Town. My old Hobby King charger does not measure Internal Resistance (IR) so decided to upgrade but will still use my Quattro 4x6.

I got a big shock when I tested the first battery which had come to its useful life many years ago!

My batteries are stored safely but accidents can happen so I will now check all my batteries and think I will be disposing of most of them though they have given me good service.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

https://flyingrobot.co/  What a great name for a quad copter shop!

Name of Video YouTube Link Published
Basic Quad Copter Set Up Part 5 Jumper T16 Screen Configuration
https://youtu.be/QB51Z3RAYWE
10/07/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX and Betaflight. Here I go through setting up the Jumper T16 screen the way I like but please change things to your liking.

This tutorial is from a newbie’s point of view, I have only set up 2 quad copters before this one. I have set many fixed wing planes over the years oh and 1 toy grade quad copter which is set up very differently.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO
https://www.banggood.com/custlink/vv3YhAbVlH

Jumper T16 Parameters for Custom Model Pictures
https://youtu.be/YvxecbnuvAQ

Name of Video YouTube Link Published

Basic Quad Copter Set Up Part 4 On Screen Display (OSD) & Video Transmitter (VTX)

https://youtu.be/a1T-T3dalEI
08/07/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX and Betaflight. Here I go through the OSD & VTX.

This tutorial is from a newbie’s point of view, I have only set up 2 quad copters before this one. I have set many fixed wing planes over the years oh and 1 toy grade quad copter which is set up very differently.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO
https://www.banggood.com/custlink/vv3YhAbVlH

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.1.36 Available Now

https://youtu.be/iGrUcxVP0PA
06/07/20

There is an update available for your multiprotocol module in your Jumper T16 I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published

Another Syma flight and it went down!

https://youtu.be/rTUksItxKG0
06/07/20

Saturday morning flight and my Syma lost control but I used my video signal to help locate it and we were reunited! What a view from the top of the hill I must go climb it to the top soon.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Basic Quad Copter Set Up Part 3 Betaflight Configuration

https://youtu.be/rdGRUq5JnXY
03/07/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX and Betaflight. Here I go through the Betaflight Configuration and what was missing from the stock set up.

This tutorial is from a newbie’s point of view for newbie’s.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO

https://www.banggood.com/custlink/vv3YhAbVlH
Name of Video YouTube Link Published

Basic Quad Copter Set Up Part 2 Bind & Telemetry

https://youtu.be/BQVhwNpKSCQ
01/07/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX. Here I go through binding the quad copter to the Jumper T16 and taking a look at the telemetry yes the little Eachine E010S Pro sends back telemetry to your radio!

This tutorial is from a newbie’s point of view, I have only set up 2 quad copters before this one. I have set many fixed wing planes over the years oh and 1 toy grade quad copter which is set up very differently.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Jumper T16 FrSky Frequency Adj.
https://youtu.be/RDICdD4QpUk

Jumper T16 Not Binding to Frsky V8R4 Receiver
https://youtu.be/Zm5_mKAPjPU

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO

https://www.banggood.com/custlink/vv3YhAbVlH
Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.1.24 Available Now

https://youtu.be/gpkdP0RpVy8
29/06/20

There is an update available for your multiprotocol module in your Jumper T16 I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published

Basic Quad Copter Set Up Part 1 Radio & Maiden Flight

https://youtu.be/OFgUGgwbSA0
29/06/20

This video is part of a series showing you how to set up a quad copter from start to finish in the Jumper T16 using OpenTX. Here I go through your radio settings from basic model, see link below, setting up Inputs & Mixes & Special Functions (sounds) connected to your switches. Then the really fun bit the maiden flight.

This tutorial is from a newbie’s point of view, I have only set up 2 quad copters before this one. I have set many fixed wing planes over the years oh and 1 toy grade quad copter which is set up very differently. If interested in the toy grade copter set up there is a link below to my video.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Basic Model Set Up (time frame 0:00 to 1:54)
With one proviso your aileron should be on one channel and not two as shown in my video.
https://youtu.be/DvJFPIjTdEo

Setting Up a Toy Grade Copter in OpenTX
https://youtu.be/x0BgPL8T410

Making Custom Sounds
https://youtu.be/aO3wYejJs00

Please see link below if you would like to purchase the item. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. You will pay no more for the product, thank you.

I did purchase the Eachine E010S PRO with my own money.

Eachine E010S PRO

https://www.banggood.com/custlink/vv3YhAbVlH
Name of Video YouTube Link Published

Jumper T16 OpenTX Bind on Channel

https://youtu.be/QrpGOKP8dqg
24/06/20

This video shows you how to set up the Bind on Channel option in your Jumper T16 using OpenTX

I have found this particularly useful for my Syma X5C-1 quad copter.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Making Custom Sounds
https://youtu.be/aO3wYejJs00

Name of Video YouTube Link Published
Turnigy TGY 9X Using as a Controller for Liftoff Sim
https://youtu.be/BPBoLVJJhsA
17/06/20

This video shows you want you need to have to use your non USB radio as a controller for the drone simulator Liftoff. You will need a 3.5mm stereo jack lead and download the SmartPropoPlus program see link below.

It is not as smooth as my Jumper T16 and Taranis X-Lite but if it is the only radio you have it will allow you to practice flying in a simulator.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Liftoff Drone Simulations
https://www.liftoff-game.com/

SmartPropoPlus

http://smartpropoplus.sourceforge.net/site/
Name of Video YouTube Link Published

OpenTX Firmware Update 2.3.9 Available Now

https://youtu.be/FdNcn_al5Ec
14/06/20

There is an update available for OpenTX version 2.3.9, which corrects the problems with 2.3.8, which is available for download now. I have updated my radio with no problems or error messages.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Open TX
https://www.open-tx.org/

Video how to update your firmware
https://youtu.be/l4YE5nBe-lw

OpenTX - My Procedure For Updating SD Card Contents
https://youtu.be/7YXfGNqSiMM

Name of Video YouTube Link Published

OpenTX Update 2.3.8 Problem Download Disabled!

https://youtu.be/FdNcn_al5Ec
14/06/20

Hi Everyone,

There seems to be a problem with the latest version of OpenTX so it may be advisable if you managed to update to revert back to version 2.3.7

Bill.

Name of Video YouTube Link Published

OpenTX Firmware Update 2.3.8 Available Now

https://youtu.be/3HHA3BzoUQE
14/06/20

There is an update available for OpenTX version 2.3.8 which is available for download now. I had a couple of issues with my update but easily solved, please see in my video.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Open TX
https://www.open-tx.org/

Video how to update your firmware
https://youtu.be/l4YE5nBe-lw

OpenTX - My Procedure For Updating SD Card Contents
https://youtu.be/7YXfGNqSiMM

Name of Video YouTube Link Published

Turnigy TGY 9X Battery Calibration

https://youtu.be/eBCvbptPMxQ
12/06/20

This short video shows you how to calibrate your Turnigy TGY 9X battery and input the value into your radio.

Keep safe out there.

Thanks for watching, happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.1.9 Available Now

https://youtu.be/RFOMVYFiwio

03/06/20

There is an update available for your multiprotocol module in your Jumper T16 I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published

Turnigy TGY9X Setting Up Flaperons with OpenTX

https://youtu.be/n0Y4EPum9uI
03/06/20

In this video I show you how to set up flaperons in your Turnigy TGY9X. If your ailerons are actuated by 2 servos 1 in each wing you can use these settings to have flaps as well. There is just one thing you need to take into consideration is the amount of flap if you set to much you may loss aileron authority so I would suggest experimenting with the amount slowly increasing it.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Links:

Setting up a model in your Turnigy TGY9X
https://youtu.be/DD6scu2VkQQ

Name of Video YouTube Link Published

How to Update FrSky Receiver Firmware with FrSky Taranis X-Lite

https://youtu.be/hWEBvJOuMT0
29/05/20

I recently update my FrSky receiver’s firmware with D16 V2.1.0 and I thought I should share the process with you. It is not difficult you just need to make sure you wire your leads and plugs correctly.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Links:

FrSky Firmware Updates
https://www.frsky-rc.com/download/

OpenTX - My procedure for updating SD Card contents
https://youtu.be/7YXfGNqSiMM

Name of Video YouTube Link Published

Jumper T16 Setting Up Trainer Mode

https://youtu.be/2AK_eFCea-8
25/05/20

This video shows you how to set up the Master & Slave radios in OpenTX so you can help teach a friend to fly RC models. I used my Jumper T16 as the Master and my Turnigy TGY9X as the slave and they worked a treat.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Jumper T16 Model Menu Episode 1 – Model Setup
https://youtu.be/1XgpyYt4mPE

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.1.1 Available Now

https://youtu.be/9MvlJUZVqy8
24/05/20

There is an update available for your multiprotocol module in your Jumper T6 I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published
How to Update FrSky Receiver Firmware using your Jumper T16
https://youtu.be/Zp4NFljI9vE
22/05/20

I recently update my FrSky receiver’s firmware with D16 V2.1.0 and I thought I should share the process with you. It is not difficult you just need to make sure you wire your leads and plugs correctly.

What prompted me to do the firmware updates was the dev’s at multi-module.org added the protocol to the list of protocols in your module.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Links:

FrSky Firmware Updates
https://www.frsky-rc.com/download/

Multi-Protocol Module Updates
https://www.multi-module.org/

How to update your multi-protocol module firmware
https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published
Jumper T16 Crow Butterfly Brakes in OpenTX
https://youtu.be/xDag1xlsY28
18/05/20

In this video I show you how to program crow / butterfly brakes in your Jumper T16 using OpenTX. I have never used crow brakes as I have only built one basic glider before so this will show you how to set the mixes up and you will need to adjust the Global Variables (GV’s) to your preferences.

Thanks for watching.

Happy Flying.

Links:

Jumper T16 Setting Up Flaperons in OpenTX
https://youtu.be/eHs6_YhhRwI

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Back to LOS'ing In My Favourite Field! https://youtu.be/6uwMQUoV-yQ
16/05/20

Just me enjoying myself back in my favourite flying field. Two packs in my fixed wing Clouds plane and three packs in my Taycan. Happy days :)

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Setting Up Flaperons in OpenTX

https://youtu.be/eHs6_YhhRwI
15/05/20

In this video I show you how to set up flaperons. If your ailerons are actuated by 2 servos 1 in each wing you can use these settings to have flaps as well.

Thanks for watching.

Happy Flying.

Links:

Jumper T16 Making a Custom Sound
https://youtu.be/aO3wYejJs00

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Model Menu Episode 2 – Flight Modes to Telemetry

https://youtu.be/qnJgPYTqcJ8
11/05/20

This is my final video going through all the screens of your Jumper T16.

This video is going through the Model Setup Menu, Flight Modes to Telemetry.

Thanks for watching.

Happy Flying.

Links:

Jumper T16 Setting Up Flight Modes
https://youtu.be/ysa30dUq0X0

Jumper T16 Setting Up Quad Copter Flight Modes
https://youtu.be/lTmL9R5BplU

Setting Up Dual Rates in Open TX for the Jumper T16
https://youtu.be/Vv0ibtLni-A

Jumper T16 Setup Model with Elevons
https://youtu.be/CsIs-Dzd90M

Jumper T16 Using Global Variables to set up Aileron Differential
https://youtu.be/05dfw6z8yh0

Jumper T16 Setting Up A "Safe" Throttle
https://youtu.be/B6jbDA7a10s

Jumper T16 Making a Custom Sound
https://youtu.be/aO3wYejJs00

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.0.95 Available Now

https://youtu.be/miIwRXKPNBI
09/05/20

There is an update available for your multiprotocol module in your Jumper T6 I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published
Jumper T16 Using Global Variables to set up Aileron Differential
https://youtu.be/05dfw6z8yh0
08/05/20

This video will give you an idea of what global variables are and what they are used for. This example is for Aileron Differential which is used to make the downward aileron have less throw than the upward one. This helps the downward aileron cause less drag and can help with adverse yaw.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Model Menu Episode 1 – Model Setup

https://youtu.be/1XgpyYt4mPE
06/05/20

I am going to produce a series of videos walking you through all the screens of your Jumper T16.

This video is going through the Model Setup Menu.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 System Menu Episode 4 – Hardware & Version

https://youtu.be/tbMnNjP9GXk
04/05/20

I am going to produce a series of videos walking you through all the screens of your Jumper T16.

This video is going through the System Menu – Hardware & Version.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 System Menu Episode 3 Global Functions & Trainer
https://youtu.be/-yyDCraJ1ig
02/05/20

I am going to produce a series of videos walking you through all the screens of your Jumper T16.

This video is going through the System Menu – Global Functions & Trainer options.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 System Menu Episode 2 - Radio Set Up
https://youtu.be/cotMhSe0nKU
01/05/20

I am going to produce a series of videos walking you through all the screens of your Jumper T16.

This video is going through the System Menu – Radio Set Up options.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Turnigy TGY 9X Setting Up Flight Modes

https://youtu.be/-x-XskQNoqk
29/04/20

Just a quick video to show you how to set up Flight Modes in your Turnigy TGY 9X

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 System Menu Episode 1 - Tools & SD - HC Card
https://youtu.be/B1ti0VkG-hM
27/04/20

I am going to produce a series of videos walking you through all the screens of your Jumper T16.

This video is going through the System Menu – Tools & SD-HC Card options.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Custom Widget Colours

https://youtu.be/Yu4a75kaD-I
24/04/20

Just short video to show you how to change the screen colours on your Jumper T16

Changed by to green of cause!

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Online Colour Charts.
https://htmlcolorcodes.com/color-chart/

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.0.91 Available Now

https://youtu.be/W1kpuEFByrU
22/04/20

Short video to let you know an update is available for your multiprotocol module I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/8fwU220sVKc

Name of Video YouTube Link Published

Turnigy TGY 9X Setting Up A “Safe Throttle”

https://youtu.be/g2vGBEo91_M
22/04/20

In this video I show you how to set up a safe throttle in OpenTX Companion and on your radio. I would recommend this for all electric powered fixed wing model as it will help stop accidental arming of your models motor.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 How To Update Your Multiprotocol Module Firmware

https://youtu.be/8fwU220sVKc
20/04/20

How to download firmware updates and install on your Jumper T16’s multiprotocol internal module.

Thanks for watching.

Happy Flying.

https://downloads.multi-module.org/

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.0.89 Available Now

https://youtu.be/WUqNFdfLSdE
19/04/20

Short video to let you know an update is available for your multiprotocol module I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/CECcliqzN1c

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.0.88 Available Now

https://youtu.be/sW5HY-lM2Yw
17/04/20

Short video to let you know an update is available for your multiprotocol module I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/CECcliqzN1c

Name of Video YouTube Link Published

Jumper T16 Setting Up Quad Copter Flight Modes

https://youtu.be/lTmL9R5BplU
17/04/20

A video to help set up quad copter flight modes in your Jumper T16.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update v1.3.0.87 Available Now

https://youtu.be/omYXE0NbKu0
16/04/20

Short video to let you know an update is available for your multiprotocol module I update my module with no problems.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Video how to update your firmware

https://youtu.be/CECcliqzN1c

Name of Video YouTube Link Published

Jumper T16 Battery % Widget Set Up

https://youtu.be/CO5RgNhlkGE
15/04/20

It was a little confusing trying to get the battery % in my radio to reflect the correct readings.

Here is how I did it.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

OpenTX - My Procedure For Updating SD Card Contents

https://youtu.be/7YXfGNqSiMM
13/04/20

This is the way I update my SD Card contents for my OpenTX radios making sure I keep my custom pictures, custom sounds & lua scripts.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Setting Up Flight Modes

https://youtu.be/ysa30dUq0X0
10/04/20

A video to help set up flight modes in your Jumper T16. Useful for both quads & fixed wing models.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Turnigy 9X Model Setup in OpenTX Companion & on the Radio

https://youtu.be/DD6scu2VkQQ 
08/04/20

This video will help you setup a model on your radio using OpenTX Companion and then on the radio directly.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Slowing Servo Speed

https://youtu.be/0DfER6N7eGA 
06/04/20

A short video prompted by one of my subscribers it was a good question about slowing servo speed.

I hope you all found this video useful.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Battery Calibration

https://youtu.be/r30APiPwzyU
06/04/20

A short video to help you complete battery calibrate on your Jumper T16. You will need to have or borrow a multi meter to complete this task and I prefer to charge my batteries fully before doing this process.

I hope you found this video useful.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Turnigy 9X Backup & Restore Settings with OpenTX Companion

https://youtu.be/VAuGoQNyohw
03/04/20

This video will help you backup and restore your radio settings and models using the OpenTX Companion.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

What is Jello? No not the dessert.

https://youtu.be/c7M3aEA6rI0 
01/04/20

On my Christmas video helping out Father Christmas the video had a major amount of “jello”
This video explains what jello is and how to try and stop it.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update Pre-Release v1.3.0.79

https://youtu.be/nJ27goSLn7o 
31/03/20

Short video to let you know an update is available for your multiprotocol module. I am not going to update my internal module with this release at the moment please see video for my reason.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Name of Video YouTube Link Published

Jumper T16 Range Test Function

https://youtu.be/0Y46eTUFBfo 
30/03/20

A short video explaining the Range function of the Jumper T16 radio.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Hold Off! Updating Your Jumper T16 with OpenTX 2.3.6
https://youtu.be/GzGG0lW-dYg 
28/03/20
Please hold off updating your radio with OpenTX 2.3.6. It just put my radion into Emergency Mode. A new update is coming as per the OpenTX website which will be 2.3.7
Name of Video YouTube Link Published

Jumper T16 OpenTX Update 2.3.6 Available

https://youtu.be/5qvTzaxjFyw 
28/03/20

Hi Everyone, There is a new version of the OpenTX firmware available for your Jumper T16 version 2.3.6

Please leave comments in the comments section below.

My how to update your firmware video:

https://youtu.be/l4YE5nBe-lw

OpenTX https://www.open-tx.org/

OpenTX Companion & Latest Fimware

https://www.open-tx.org/downloads

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 OpenTX Receiver Number Explained
https://youtu.be/SA-q4n_WqWU 
27/03/20

This is a great feature of the radio when you bind your receiver to the radio if you give it a receiver number you can transfer the receiver to another model and pick the receivers assigned number and you are ready to go without having to bond the receiver again.

Cool feature!

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 OpenTX Timer Options
https://youtu.be/_3tc2V0B3ho
25/03/20

Setting up timers in your Jumper T16 the different types and how to reset them.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Make Your Craft More Visible for LOS

https://youtu.be/SC8G6we5TOI
23/03/20

I fly RC planes and quad copters and when you are flying Line Of Sight you need to have a reference point on your craft to help you workout its orientation with reference to your position. I paint my planes with contrasting colours to help with orientation with scale planes you need to rely on their shape for orientation.

With more practice LOS flight becomes second nature.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Multiprotocol Module Update Release v1.3.0.76

https://youtu.be/bAorg1pvcvs 
22/03/20

Short video to let you know an update is available for your multiprotocol module.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

https://downloads.multi-module.org/

Name of Video YouTube Link Published
Jumper T16 Setup Model with Elevons https://youtu.be/CsIs-Dzd90M
20/03/20

How to setting up elevons on your wing model. I found it easier to set up the model in the OpenTX Companion than on the Jumper T16 because of the option it gives you for Flying Wing / Delta Wing. You just need to be careful of your channel mapping.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Setting Up Rudder and Aileron Mixing

https://youtu.be/ssBX8ikbdPc 
18/03/20

Some model aircraft will only roll when actuating the ailerons so you may have to coordinate rudder input as well. With the onset of computer radios and OpenTX you can now add a mix so your aileron stick actuates the rudder at the same time to a limit you can set.

Here is how to do it.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Turnigy 9X Flashing with OpenTX

https://youtu.be/hZgmglf8tUs
16/03/20

Following on from my video discussing the conversion of my Turnigy TGY9X here is my full video of the conversion process which is well worth the effort because OpenTX is better than the stock firmware.

Any questions please leave them in the comments section below.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Links:

eePe-EEPROM Editor - https://www.er9x.com

OpenTX Companion 2.1 - https://www.open-tx.org

Below is an affiliate link which if you click on and make a purchase I will receive a small commission to help me produce more content for my channel, Thank You.

5V Micro USB Tiny AVR ISP ATtiny44
https://www.banggood.com/custlink/mm3mkcMBP7

Name of Video YouTube Link Published

Setting Up Dual Rates in Open TX for the Jumper T16

https://youtu.be/Vv0ibtLni-A
13/03/20

This video will explain how to set up dual rates for Ailerons, Elevators and or Rudder on a fixed wing plane. This will help with a fast reacting model reducing your roll rates I normally set up my dual rates at 60% of the full throw.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Setting Up Expo in OpenTX https://youtu.be/r6hjgvSnH9M
11/03/20

This video will explain what expo is when used with Ailerons, Elevators and or Rudder on a fixed wing plane. It is a very useful feature to help smooth out the controls of a twitch plane I normally set my expo’s to 25%

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Banggood Promotion - FPV RC Drone Spring Flying

Below is an affiliate link which if you click on and make a purchase I will receive a small commission to help me produce more content for my channel. Thank You.

https://www.banggood.com/custlink/mGGvzEzJza

Name of Video YouTube Link Published
Turnigy TGY 9X Conversion to OpenTX
https://youtu.be/JWeKweniiUo 
10/03/20

I have been working on and off on converting my two Turnigy TGY 9X radios to openTX but came across a problem which I have now sorted out. The video explains all.

The 9X does not compare to the Jumper T16 but is value for money and far better with OpenTX instead of the stock firmware they are still available from Hobby King which must give us an idea how reliable the radios are still being sold 10 years later.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Turnigy 9X is available from Hobby King, this is not an affiliate link.

https://hobbyking.com/en_us/turnigy-9x-9ch-mode-2-transmitter-w-module-ia8-receiver-afhds-2a-system.html

Name of Video YouTube Link Published
Jumper T16 Range Testing https://youtu.be/gTBvTUyN5fU
09/03/20

I remember in the “old” days with FM transmitters to range check we lowered the huge aerial and walked away with the model and looked for the servo glitching, no glitching at a specified distance all was good. With 2.4Ghz I was not sure how to do this with non telemetry receivers. Here’s my attempt with interesting results.

I did try to find the range test distances for the 3 receivers I used in my test but not even the Frysky manual for the XM+ gave this information.

Not very scientific I agree but you can use the information as you wish.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Below is an affiliate link which if you click on and make a purchase I will receive a small commission to help me produce more content for my channel. Thank You.

Banggood Promotion - RC Quadcopter & Parts

https://www.banggood.com/custlink/GvGKzEzJ1p

Name of Video YouTube Link Published
Beautiful Morning to Fly https://youtu.be/0Xy1Egf14xQ
07/03/20

The morning weather was so perfect I went to fly the Syma X5C-1 Still waiting for my packages from China so the Syma will have to do.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
What helped improve my soldering
https://youtu.be/edeFJNPh3hY 
06/03/20

For a long time I used a cheap soldering iron and my soldering was substandard. When I started to fly quads there was a necessity to be able to solder reasonable to make repairs. I have needed to solder the receiver wires on my Betafpv 75X a few times. What improved my soldering was buying a good but not expensive soldering station.

I did use my own money to purchase the soldering station in this video.

Thanks for watching.

Happy Flying.

 https://www.patreon.com/BillClark

Please see link below if you would like to purchase the one I use. This is an affiliate link so I would make a small commission if you purchase via my link this would help me produce more content for my channel. Thank you.

Quicko T12-942 MINI OLED Digital Soldering Station:

https://www.banggood.com/Quicko-T12-942-MINI-OLED-Digital-Soldering-Station-T12-907-Handle-with-T12-K-Iron-Tips-Welding-Tool-p-1326151.html?rmmds=myorder&cur_warehouse=CN&p=YV100333357251202002&custlinkid=818300

Spare Soldering Iron Tips T12 series:

https://www.banggood.com/custlink/33GDMR2HGO

Name of Video YouTube Link Published

Flying the Syma X5C-1 in Air Mode

https://youtu.be/MRC6tMgUj6o
04/03/20

I wanted to show the quad copter being flown in Air Mode which makes a big difference to its flight characteristics. It has been a big learning curve setting up the quad copter to the Jumper T16 and well worth the effort I would recommend giving it ago.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

You can get one at Takealot.com
https://www.takealot.com/syma-x5c-quadcopter-drone-with-2-0mp-camera/PLID42979232

Name of Video YouTube Link Published

Jumper T16 Setting Up Air Mode for Syma X5C-1

https://youtu.be/qOAj0-E294c
02/03/20

When flying my Syma X5C-1 with my Jumper T16 radio when you cut the throttle the motors stopped and so did the quads stabilisation. In the website I mentioned in my set up of the quad it suggested you set up a rudimentary “air mode”. When I did this I wanted to be able to deactivate it with a switch but had problems with the switch overriding the disarmed switch this could lead to the motors spinning when disarmed this I was not happy with. This is how I solved the problem.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Setting Up Toy Grade Quad Copter - Throttle Mod

https://youtu.be/ccK0Zou-2RA 
28/02/20

Here is a short video showing you how to set up a “safe” throttle for the toy grade quad copter I recently showed in one of my videos being set up and bound to my Jumper T16.

Thanks for watching.

Happy flying.

Full Video - Jumper T16 Setting Up A "Safe" Throttle
https://youtu.be/B6jbDA7a10s

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Screen Setup 
https://youtu.be/4-gUjokOM8U 
26/02/20

Following on from my previous video here is how to customise your Jumper T16 opening screen.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Basic Model Set Up - 4 Channel Fixed Wing

https://youtu.be/DvJFPIjTdEo 
24/02/20

One of my viewers asked me if I could make a video of a basic model set up in the Jumper T16, I of cause was happy to help.  This is a long video but I do go into detail of how to set your model up.

There will be a video following soon of how to add widgets to your Jumper T16 fantastic screen especially the timer I set up in this video.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 Setting Up A "Safe" Throttle

https://youtu.be/B6jbDA7a10s 
21/02/20

When setting up a new fixed wing model I accidentally armed the motor with the throttle raised and luckily I had a good grip on the model or it would have been an unguided missile in my house. With quad copters the flight control in conjunction with the radio controls the arming so if the throttle is raised the quad copter will not arm.

Searching the internet I found 2 methods one, whatever I did, would not work and the second did. I did not wanted to do the programming in OpenTX Companion because, as I understand, all my models would need to be bound to the transmitter again once I restored them. When doing the process on the Jumper T16 the terminology did not match with OpenTX Companion with slight differences. So I decide to make this video so it you want to set this feature up without really understanding the programming side of things here it is just copy my screens.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Throttle Sensitivity Adjustment
https://youtu.be/U076QvEm0aY 
17/02/20

I have been flying RC model aircraft for just over 30 years and always set up the throttle on my radio with a ratchet but I have noticed when flying quad copters the throttle needed to be more sensitive so switched to a smooth throttle. On my Jumper T16 I could not get the throttle tension stiff enough because I was use to the firmer ratchet throttle, this is my solution.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Making a Custom Sound
https://youtu.be/aO3wYejJs00 
12/02/20

On my latest model quad copter I have a flip mode and wanted to make a sound for when it was deactivated. It is not a difficult procedure let’s show you how.

Thanks for watching.

Happy flying.

Odd Cast

http://ttsdemo.com/

Audiocity

https://www.audacityteam.org/

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Set Up As Liftoff Controller
https://youtu.be/K_7Z1cMGzIQ
10/02/20

Here is a quick video to help you set up your Jumper T16 as a flight controller to use with the Liftoff quad simulator.

Thanks for watching.

Happy flying.

Liftoff

https://www.liftoff-game.com

https://store.steampowered.com/app/410340/Liftoff_FPV_Drone_Racing/

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
How to Make Sounds Play in OpenTX Companion
https://youtu.be/0GxTOvPB_TA
07/02/20

A viewer asked me if I could help with a problem of sounds not playing in OpenTX Companion. Here is my answer to solve the problem.

I hope you find this video helpful.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Setting Up A Toy Grade Quad Copter
https://youtu.be/x0BgPL8T410
05/02/20

I was interested in trying to set up a toy grade quad copter on my Jumper T16, it was very easy to do so with the help of the links below.

Thanks for watching.

Happy flying.

Model Set Up

https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/docs/Models.md

https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Restoring OpenTX Model & Radio Settings to the Jumper T16
https://youtu.be/lmf-1cG8I04
31/01/20

In this video I will show you how to back up your Jumper T16 model & radio settings to a file on your computer and then restore them back to your radio.

Once you have restored your settings please treat your models as if they are a new build for safety reasons just in case the settings are not exactly the same.

You will also need to bind your model receivers as this is lost on restoring your settings from the back up.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Parameters for Custom Model Pictures
https://youtu.be/YvxecbnuvAQ
30/01/20

A quick video on the way to produce your custom model photograph’s for your Jumper T16.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published

Jumper T16 OpenTX SDCard Set Up with New Card Contents

https://youtu.be/9B_guG_b7vw
27/01/20

Following on from my video Installing OpenTX Companion & Updating Jumper T16 Firmware here is my video of setting up your SDCard with Amber sounds, Betaflight TX lua scripts, custom sounds & model pictures. First you need to put the OpenTX SDCard Contents on the SDCard and then all other items after this.

Hope you find this video useful.

Thanks for watching.

Happy flying.

OpenTX

https://www.open-tx.org/

OpenTX SDCard Contents

https://downloads.open-tx.org/2.3/release/sdcard/

OpenTX Amber Sound Pack

http://open-txu.org/home/version-2/v2-2-resources-2/

PeaZip

https://www.peazip.org/

Betaflight TX Lua Scripts

https://github.com/betaflight/betaflight-tx-lua-scripts/releases

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RC Off Road Battery Box Conversion
https://youtu.be/FxoOFYtte3s
24/01/20

The battery that was supplied with the RC car I recently converted to FPV was only a AA 700mAh NiCd pack which only lasted a few minutes after I added the FPV Camera & VTX. I upgraded to 4 AA 2300 mAh batteries and now it runs for over 25 minutes!

Thanks for watching.

Happy driving.

https://www.takealot.com/cx1809-4wd-monster-truck-rock-climber/PLID55076390

Music:
Race Car
Rondo Brothers

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Installing OpenTX Companion & Updating Jumper T16 Firmware
https://youtu.be/l4YE5nBe-lw
22/01/20

Hi Everyone,

I had a request from a viewer to produce a video showing how to update the firmware on a Jumper T16 using the OpenTX Companion support software, here it is I hope you all find it useful.

This video is for radios that already have the bootloader installed on the internal multi protocol module and OpenTX firmware and not JumperTX firmware. If your radio has no bootloader please see the links to videos to help you below. 

Please leave comments in the comments section below.

OpenTX

https://www.open-tx.org/

OpenTX Companion & Latest Fimware

https://www.open-tx.org/downloads

Latest SDCard Contents List - Please Note: This may change.

https://downloads.open-tx.org/2.3/release/sdcard/opentx-t16/

Installing Bootloader on to Jumper T16 Internal Multi Protocol Module

Joshua Bardwell
https://www.youtube.com/watch?v=2PSLgG3QhSg

TMACFPV
https://www.youtube.com/watch?v=Dex92d7IQWI

Thanks for watching.

Name of Video YouTube Link Published
Sunday Morning RC Flight with the Baboons
https://youtu.be/PXfY0Vsz3Tw
20/01/20

Decided to go do a couple of flights with my Clouds RC plane, the Baboons were not to happy.

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 Multi Protocol Internal Module Firmware Update 1.3.0.53 https://youtu.be/CECcliqzN1c
18/01/20

Hi Everyone,

Here is how you update your firmware on your Jumper T16 multi protocol internal module.

My Jumper T16 internal multi protocol module did not come with a bootloader because I have an earlier version so I did the bootloader update which requires a CP2102 USB-to-Serial adaptor. Please see below for links to videos of how to do this. You will need to do this if you module does not have a bootloader installed.

Joshua Bardwell
https://www.youtube.com/watch?v=2PSLgG3QhSg

TMACFPV
https://www.youtube.com/watch?v=Dex92d7IQWI

Firmware Updates Available From
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/releases

I hope you found this video useful.

Thanks for watching.

Happy flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
Jumper T16 OpenTX 2.3.5 Critical Update https://youtu.be/kbzq8munATI
13/01/20

Yesterday OpenTX released a new firmware version which fixes a critical problem with the Jumper T16 I wanted to let everyone know about the new firmware so they do not lose any of their precious model planes or quadcopters!

Link to OpenTX
https://www.open-tx.org/2020/01/15/opentx-2.3.5

Thanks for watching.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
My 75 Year Old Friend Madge's First FPV Experience! https://youtu.be/4CoMTqSQRuM
10/01/20

This was a really fun video to make. My friend Madge is 75 years old and this is her first FPV experience.

This is very funny.

Thanks for watching.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RC Off Road Truck Conversion to FPV Update
https://youtu.be/CIlNjFzNEv8
09/01/20

I did a modification to the RC truck I converted to FPV to protect the VTX antenna, here's the video.

Thanks for watching.

Music:
Sunrise Drive
South London HiFi

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RC 4126 Cheetah Glider Conversion Update
https://youtu.be/EvJJgULCoG8
07/01/20

After a couple of flights of the Cheetah RC plane I realized I needed to add a carbon fiber spar to stop the wing from bending in flight. Here's how I did it.

Happy Flying.

https://www.patreon.com/BillClark

Name of Video YouTube Link Published
RC Off Road Truck Conversion to FPV https://youtu.be/MoWoIn-sv-A
06/01/20

I watched a video of a FPV racing car you can buy which where I live I would only be able to use in my house so I decided to buy an off road RC car and add FPV. I think it worked out great.

FPV Camera Used, Available from Amazon:
Wolfwhoop WT03 Micro FPV AIO 600TVL Camera 5.8G 25mW/50mW/200mW Adjustable Transmitter with Cloverleaf Antenna.

https://www.amazon.com/Wolfwhoop-Adjustable-Transmitter-Cloverleaf-Aircraft/dp/B06XB2ZRBP

RC Truck Available from Takealot.com

https://www.takealot.com/cx1809-4wd-monster-truck-rock-climber/PLID55076390

Music:
Sunrise Drive
by South London HiFi

Please like, share and subscribe to help me produce more content on my channel.

Thanks for watching.

https://www.patreon.com/BillClark